Why does my car radio show SAFE or CODE?

SAFE or CODE appears because the anti-theft system activates after power loss (battery disconnect, replacement, or radio removal). The unit requires the correct security code to unlock.

How many attempts do I have to enter the radio code?

Most units allow a limited number of attempts (often 3). After too many wrong tries, the radio may lock temporarily and require waiting time with ignition on before retrying.

Where can I find my radio serial number?

The serial number is usually on the radio label (side/top) and may require sliding the radio out. Some models can also display it on-screen using specific button combinations.

What if the code is correct but the radio stays locked?

Double-check the exact entry method for your model and confirm the radio has not been swapped. If the unit shows a timed lock or error state, you may need to wait before trying again.

Get Nissan Juke Radio Codes Now | Connect, Clarion, Daewoo

Nissan Juke Radio Unlock • Serial Number Guide

How To Find Your Nissan Juke Serial Number

Nissan Juke radios do not all use the same unlock method. Some Connect and Daewoo units show the serial details on the screen, while Clarion units usually need the radio label. Use this guide to find the correct serial number before ordering your Nissan Juke radio code.

✅ Bosch Connect screen method ✅ Daewoo screen method 🏷️ Clarion label method 📸 Photo = fewer mistakes

First identify your radio type. Then copy the numbers exactly as shown on the screen or label.

Bosch LCN EU Daewoo Clarion Serial label Enter code Radio locked By model

Nissan Connect Bosch LCN EU Radio

Screen shows Serial + Device + Date

What you will see

When the radio is switched on, CODE appears on the display. After three incorrect attempts, the radio can show the information needed for decoding.

Step-by-step method

Turn the radio on and wait for CODE.
Enter 3 incorrect codes.
Press OK after each attempt.
After the third attempt, the screen should show System is locked for 60 minutes.
Copy the Serial Number, Device Number, and Date.

Nissan Connect Bosch systems display the required information on the screen. You do not need to remove the radio.

Unfortunately, radios that display the date 30.39.30 cannot be decoded by us.

Nissan Juke Connect Bosch LCN EU radio code retrieval screen

Reference image: copy Serial / Device / Date exactly as shown.

Nissan Daewoo

Screen shows Serial + Part + Date

Quick method

Many Nissan Juke Daewoo radios show decoding details on the display after repeated incorrect entries.

Switch on the ignition.
RADIO CODE is displayed on the screen.
Enter an incorrect code 3 times, for example 1-2-3-4.
Copy the Serial Number, Part Number, and Date.

Make a note of these numbers and copy the date exactly as displayed.

Some Daewoo radios need to be removed because the screen date may not match the correct date on the radio label.

Nissan Daewoo radio screen displaying serial number part number and date

Reference image: look for Serial / Part / Date on the screen.

Nissan Clarion

Serial is on the radio label

Why removal is needed

For Nissan Clarion radios, the serial number is usually printed on the label. You may need a pry tool or flathead screwdriver to remove the dash panel and access the radio.

Common format:
Model Number: PP3001
Serial Number: PP3001 0771234

It can also be a 14-character serial such as CLxxxxxx0768345, with the last 7 digits often starting with 0.

Do not use VIN/chassis for Clarion decoding. Use the label serial instead.

Nissan Clarion radio code display and serial label reference

Reference image: Clarion serial is best read directly from the label.

Your Nissan Serial Number On The Label

Top or side of radio housing

If the radio has been removed, locate the label on the top or side of the radio housing. The example image highlights the information usually needed for decoding.

Take a clear photo of the full label and a close-up photo of the serial number.

Nissan Juke radio serial number label example

Reference image: use the serial shown on the radio label.

How To Enter Nissan Juke Radio Code

Enter carefully

Entering the radio code in a Nissan Juke varies depending on the radio model installed. In many cases, you enter the code and press OK. On other units, preset buttons are used to set each digit.

Search your radio model here: enter Nissan radio code videos →

Enter the code carefully and avoid repeated wrong attempts, because the radio may lock temporarily.

My Nissan Juke Radio Is Locked

Temporary security lock

The radio may lock if too many incorrect codes are entered. On most Nissan radio models, the lock is released after about 60 minutes with the unit powered on.

Keep the ignition on and leave the radio powered until the timer finishes.

If your Touch & Connect unit shows Contact your Nissan dealer, the attempt limit may have been reached and a dealer reset may be required.

Get radio code by model

Choose your Nissan

Choose your car or radio brand to see tailored unlocking instructions.

Nissan Micra radio code Nissan Qashqai radio code Nissan Note radio code All Nissan radio codes

Nissan Juke Radio Code FAQ

Quick answers

Where is the Nissan Juke radio serial number?

It can be shown on the display for some Bosch and Daewoo units, or printed on the radio label for Clarion and other label-based units.

Can I unlock a Nissan Juke radio using VIN?

Usually no. Nissan radio codes are normally linked to the radio unit, so the serial number is the safest detail to use.

Do I need to remove my Nissan Connect Bosch radio?

No. Nissan Connect Bosch systems normally show the Serial Number, Device Number, and Date on the screen.

What if my radio says locked for 60 minutes?

Keep the ignition on and the radio powered. After the timer ends, code entry should become available again.

Helpful page: Nissan radio code page →